Properties of aluminum alloys: tensile, creep, and fatigue data at high and low temperatures / ed. by J.G.Kaufman. - Materials Park: ASM International; Washington: Aluminum Association, 2006. - x, 311 p. - ISBN-10 0-87170-632-6; ISBN-13 978-0-87170-632-4  Место хранения:   058 | Институт физики прочности и материаловедения CO РАН | Томск | Библиотека

Оглавление / Contents

Introduction .................................................... 1 Mechanical Properties ........................................... 5 Typical Mechanical Properties of Wrought and Cast Aluminum Alloys at Various Temperatures ................................ 7 Wrought Alloys: 1xxx Pure Al ................................ 7 1060-O: Typical Tensile Properties ........................ 8 1060-O: Creep-Rupture and Creep Properties ................ 8 1100-O: Typical Tensile Properties ........................ 9 1100-O: Creep-Rupture and Creep Properties ............... 10 1100-H12: Typical Tensile Properties ..................... 11 1100-H12: Creep-Rupture and Creep Properties ............. 11 1100-H14: Typical Tensile Properties ..................... 12 1100-H14: Creep-Rupture and Creep Properties ............. 13 1100-H18: Typical Tensile Properties ..................... 14 1100-H 18: Creep-Rupture and Creep Properties ............ 15 1100-H112: One Sample of 1 in. (25 mm) Plate: Tensile Properties ............................................. 15 1100-H112 One Sample of 1 in. (25 mm) Plate: Stress- Relaxation Properties .................................. 15 Wrought Alloys: 2xxx Al-Cu Alloys .......................... 16 2011-T3 Rolled and Drawn Screw Machine Stock: Typical Tensile Properties ..................................... 16 2011-T3 Rolled and Drawn Screw Machine Stock: Creep- Rupture and Creep Properties ........................... 17 2011-T451 Rolled and Drawn Screw Machine Stock: Typical Tensile Properties ..................................... 17 2011-T8 Rolled and Drawn Screw Machine Stock: Typical Tensile Properties ..................................... 18 Alclad 2014-O Sheet: Typical Tensile Properties .......... 19 2014-O: Typical Tensile Properties ....................... 20 Alclad 2014-T6 Sheet and T651 Plate: Typical Tensile Properties ............................................. 21 2014-T4 Products Except Extrusions and Die Forgings: Typical Tensile Properties ............................. 22 2014-T4 Extrusions: Typical Tensile Properties ........... 23 2014-T6 Rolled and Drawn Rod ≤8.000 in. (≤200.00 mm) Diameter: Typical Tensile Properties ................... 24 2014-T6 Rolled and Drawn Rod ≤8.000 in. (≤200.00 mm) Diameter: Creep-Rupture Properties ..................... 25 2014-T6 Extrusions ≤0.499 in. (≤12.50 mm) Thick: Typical Tensile Properties ............................. 26 2014-T6 Extrusions 0.500 to 0.749 in. (>12.50≤18.00 mm) Thick: Typical Tensile Properties ...................... 27 2014-T6 Extrusions 0.500 to 0.749 in. (>12.50≤18.00 mm) Thick: Creep-Rupture Properties ........................ 28 2014-T6 Extrusions ≥0.750 in. (≥18.00 mm) Thick, ≤25 in.2 (≤16,000 mm2) Cross-Sectional Area: Typical Tensile Properties ..................................... 29 2014-T6, -T652 Forgings ≤2.000 in. (≤50.00 mm) Thick: Typical Tensile Properties ............................. 30 2014-T6, -T652 Forgings ≤2.000 in. (≤50.00 mm) Thick: Creep-Rupture and Creep Properties ..................... 31 2014-T61 Forgings: Typical Tensile Properties ............ 32 2014-T651 Plate 0.250 to 2.000 in. (>6.30≤50.00 mm) Thick: Typical Tensile Properties ...................... 33 2014-T651 Plate 0.250 to 2.000 in. (>6.30≤50.00 mm) Thick: Creep and Stress-Relaxation Properties .......... 34 2017-T4: Typical Tensile Properties ...................... 35 2017-T4: Creep-Rupture and Creep Properties .............. 35 2018-T61: Typical Tensile Properties ..................... 36 2018-T61: Creep-Rupture and Creep Properties ............. 36 2020-T6 (Obsolete Alloy): Typical Tensile Properties ..... 37 2020-T6 (Obsolete Alloy): Creep-Rupture and Creep Properties ............................................. 38 2021- T81 Plate: Typical Tensile Properties .............. 39 2021-T81 Plate: Creep-Rupture and Creep Properties ....... 40 2024-O Products Except Extrusions: Typical Tensile Properties ............................................. 41 2024-O Extrusions: Typical Tensile Properties ............ 42 Alclad 2024-O Sheet: Typical Tensile Properties .......... 43 2024-ТЗ: Typical Tensile Properties ...................... 44 2024-T3: Creep-Rupture and Creep Properties .............. 45 2024-T36: Typical Tensile Properties ..................... 46 2024-T4 Products Except Extrusions: Typical Tensile Properties ............................................. 47 2024-T4 Products Except Extrusions: Creep-Rupture and Creep Properties ....................................... 48 2024-T4 Extrusions 0.750 to 1.499 in. (> 18.00 ≤ 35.00 mm) Thick: Typical Tensile Properties .................. 49 2024-T4 Extrusions ≥ 1.500 in. (2:35.00 mm) Thick: Typical Tensile Properties ............................. 50 2024-T6: Typical Tensile Properties ...................... 51 2024-T6: Creep-Rupture and Creep Properties .............. 52 2024-T81,-T85 ≤ 1.500 in. (≤35.00 mm) Thick: Typical Tensile Properties ..................................... 53 2024-T81, -T85 ≤1.500 in. (≤35.00 mm) Thick: Creep- Rupture and Creep Properties ........................... 54 2024-T852 Forgings 1 in. (25.00 mm) Thick: Creep- Rupture and Creep Properties ........................... 54 2024-T852 Forgings ≥3.00 in. (≥275.00 mm) Thick: Creep- Rupture and Creep Properties ........................... 55 2024-T86: Typical Tensile Properties ..................... 55 2024-T86: Creep-Rupture and Creep Properties ............. 56 2117-T4: Typical Tensile Properties ...................... 57 2124-T851 Plate 1.500 to 2.000 in. (>35.00 ≤ 50.00 mm) Thick: Typical Tensile Properties ...................... 58 2124-T851 Plate 1.500 to 2.000 in. (>35.00 ≤ Ј 50.00 mm) Thick: Creep-Rupture and Creep Properties .............. 59 2124-T851 Plate 2.001 to 3.000 in. (>50.00 ≤ 75.00 mm) Thick: Typical Tensile Properties ...................... 60 2124-T851 Plate 2.001 to 3.000 in. (>50.00 ≤ 75.00 mm) Thick: Creep-Rupture and Creep Properties .............. 61 2124-T851 Plate 3.001 to 4.000 in. (>75.00 ≤ 100.00 mm) Thick: Typical Tensile Properties ...................... 62 2124-T851 Plate 3.001 to 4.000 in. (>75.00 ≤ 100.00 mm) Thick: Creep-Rupture and Creep Properties .............. 63 2124-T851 Plate 4.001 to 5.00 in. (>100.00 ≤ 125.00 mm) Thick: Typical Tensile Properties ...................... 64 2124-T851 Plate 4.001 to 5.00 in. (> 100.00 ≤ 125.00 mm) Thick: Creep-Rupture and Creep Properties ... 65 2218-T61: Typical Tensile Properties ..................... 66 2218- T61: Creep-Rupture and Creep Properties .......... 66 2219- 0: Typical Tensile Properties .................... 67 2219-0: Creep-Rupture and Creep Properties ............... 67 2219-T37 Sheet Longitudinal to Direction of Rolling: Typical Tensile Properties ............................. 68 2219-T37 Sheet Longitudinal to Direction of Rolling: Creep-Rupture and Creep Properties ..................... 68 2219-T37 Plate Longitudinal to Direction of Rolling: Typical Tensile Properties ............................. 69 2219-T37 Plate Longitudinal to Direction of Rolling: Creep-Rupture and Creep Properties ..................... 70 2219-T6 (Experimental) Plate: Typical Tensile Properties ............................................. 70 2219-T6 Forgings, Aged 18 h at 375 °F (190 °C): Typical Tensile Properties ..................................... 71 2219-T6 Forgings, Aged 18 h at 375 °F (190 °C): Creep- Rupture and Creep Properties ........................... 71 2219-T6 Forgings, Aged 16 h at 420 °F (215 °C): Typical Tensile Properties ..................................... 72 2219-T6 Forgings, Aged 16 h at 420 °F (215 °C): Creep- Rupture and Creep Properties ........................... 73 2219-T62 Sheet: Typical Tensile Properties ............... 74 2219-T62 Sheet: Creep-Rupture and Creep Properties ....... 75 2219-T62 Plate: Typical Tensile Properties ............... 76 2219-T62 Plate: Creep-Rupture and Creep Properties ....... 77 2219-T81 Sheet: Typical Tensile Properties ............... 78 2219-T81 Sheet: Creep-Rupture and Creep Properties ....... 79 2219-T851 Plate: Typical Tensile Properties .............. 80 2219-T851 Plate: Creep-Rupture and Creep Properties ...... 81 2219-T8511 Extrusions: Typical Tensile Properties ........ 82 2219-T8511 Extrusions: Creep-Rupture and Creep Properties ............................................. 82 2219-T852 Forgings: Typical Tensile Properties ........... 83 2219-T852 Forgings: Creep-Rupture and Creep Properties ... 83 2219-T87 Sheet: Typical Tensile Properties ............... 84 2219-T87 Sheet: Creep-Rupture and Creep Properties ....... 85 2219-T87 Plate: Typical Tensile Properties ............... 86 2219-T87 Plate: Creep-Rupture and Creep Properties ....... 87 2618-T6 Sheet: Typical Tensile Properties ................ 88 2618-T6 Sheet: Creep-Rupture and Creep Properties ........ 88 2618-T651 Plate: Typical Tensile Properties .............. 89 2618-T651 Plate: Creep-Rupture and Creep Properties ...... 89 2618-T61 Forgings: Typical Tensile Properties ............ 90 2618-T61 Forgings: Creep-Rupture and Creep Properties .... 91 2618-T6511 Extrusions: Typical Tensile Properties ........ 92 2618-T6511 Extrusions: Creep-Rupture and Creep Properties ............................................. 93 Wrought Alloys: Зххх Al-Mn Alloys .......................... 93 3003-O Rolled and Drawn Rod: Typical Tensile Properties .. 94 3003-O Rolled and Drawn Rod: Creep and Stress- Relaxation Properties .................................. 95 3003-H12 Rolled and Drawn Rod: Typical Tensile Properties ............................................. 96 3003-Н12 Rolled and Drawn Rod: Creep and Stress- Relaxation Properties .................................. 97 3003-H14 Rolled and Drawn Rod: Typical Tensile Properties ............................................. 98 3003-H14 Rolled and Drawn Rod: Creep and Stress- Relaxation Properties .................................. 99 3O03-H18 Rolled and Drawn Rod: Typical Tensile Properties ............................................ 100 3003-H18 Rolled and Drawn Rod: Creep-Rupture and Creep Properties ...................................... 101 3004-O Rolled and Drawn Rod: Typical Tensile Properties ............................................ 102 3004-O Rolled and Drawn Rod: Creep-Rupture and Creep Properties ............................................ 103 3004-H32 Rolled and Drawn Rod: Typical Tensile Properties ............................................ 104 3004-H32 Rolled and Drawn Rod: Creep-Rupture and Creep Properties ............................................ 104 3004-H34 Rolled and Drawn Rod: Typical Tensile Properties ............................................ 105 3004-H34 Rolled and Drawn Rod: Creep-Rupture and Creep Properties ............................................ 105 3004-H38 Rolled and Drawn Rod: Typical Tensile Properties ............................................ 106 3004-H38 Rolled and Drawn Rod: Creep-Rupture and Creep Properties ............................................ 106 Wrought Alloys: Xxxx Al-Si Alloys ......................... 107 4032-T6: Typical Tensile Properties ..................... 107 4032-T6: Creep-Rupture and Creep Properties ............. 108 Wrought Alloys: Sxxx Al-Mg Alloys ......................... 109 5005-O Rolled and Drawn Rod: Typical Tensile Properties ............................................ 109 5005-O Rolled and Drawn Rod: Creep-Rupture and Creep Properties ............................................ 110 5005-H14 Rolled and Drawn Rod: Typical Tensile Properties ............................................ 110 5005-H18 Rolled and Drawn Rod: Typical Tensile Properties ............................................ 111 5005-H18 Rolled and Drawn Rod: Creep-Rupture and Creep Properties ............................................ 111 5005-H19 Wire: Typical Tensile Properties ............... 112 5005-H19 Wire: Creep-Rupture and Creep Properties ....... 112 5050-O: Typical Tensile Properties ...................... 113 5050-O: Creep-Rupture and Creep Properties .............. 113 5050-H34: Typical Tensile Properties .................... 114 5050-H34: Creep-Rupture and Creep Properties ............ 114 5050-H38: Typical Tensile Properties .................... 115 5050-H38: Creep-Rupture and Creep Properties ............ 115 5052-O: Typical Tensile Properties ...................... 116 5052-O: Creep and Stress-Relaxation Properties .......... 117 5052-H32: Typical Tensile Properties .................... 118 5052-H32: Creep and Stress-Relaxation Properties ........ 119 5052-H34: Typical Tensile Properties .................... 120 5052-H34: Creep and Stress-Relaxation Properties ........ 121 5052-H38: Typical Tensile Properties .................... 122 5052-H38: Creep-Rupture and Creep Properties ............ 123 5052-H112 Plate 1 in. (25.00 mm) Thick: Typical Tensile Properties ............................................ 123 5052-H112 Plate 1 in. (25.00 mm) Thick: Creep-Rupture and Creep Properties .................................. 123 5056-O: Typical Tensile Properties ...................... 124 5056-O: Creep-Rupture and Creep Properties .............. 125 5056-H32: Typical Tensile Properties .................... 126 5056-H32: Creep-Rupture and Creep Properties ............ 127 5056-H34: Typical Tensile Properties .................... 128 5056-H34: Creep-Rupture and Creep Properties ............ 129 5056-H38: Typical Tensile Properties .................... 130 5083-O: Typical Tensile Properties ...................... 131 5083-O: Creep-Rupture and Creep Properties .............. 132 5083-H111 Extrusions: Typical Tensile Properties ........ 132 5083-H321: Typical Tensile Properties ................... 133 5083-H321: Creep-Rupture and Creep Properties ........... 134 5086-O: Typical Tensile Properties ...................... 135 5086-O: Creep-Rupture and Creep Properties .............. 136 5086-H32: Typical Tensile Properties .................... 137 5086-H32: Creep-Rupture and Creep Properties ............ 138 5086-H34: Typical Tensile Properties .................... 139 5086-H34: Creep-Rupture and Creep Properties ............ 140 5154-O: Typical Tensile Properties ...................... 141 5154-O: Creep-Rupture and Creep Properties .............. 142 5154-H32: Typical Tensile Properties .................... 143 5154-H32: Creep-Rupture and Creep Properties ............ 143 5154-H34: Typical Tensile Properties .................... 144 5154-H34: Creep-Rupture and Creep Properties ............ 145 5154-H38: Typical Tensile Properties .................... 146 5154-H38: Creep-Rupture and Creep Properties ............ 147 5356-O: Typical Tensile Properties ...................... 147 5356-O: Creep-Rupture and Creep Properties .............. 148 5356-H321: Typical Tensile Properties ................... 148 5454-O: Typical Tensile Properties ...................... 149 5454-O: Creep-Rupture and Creep Properties .............. 150 5454-H32: Typical Tensile Properties .................... 151 5454-H32: Creep-Rupture and Creep Properties ............ 152 5454-H34: Typical Tensile Properties .................... 153 5454-H34: Creep-Rupture and Creep Properties ............ 154 5456-0: Typical Tensile Properties ...................... 155 5456-0: Creep-Rupture and Creep Properties .............. 156 5456-H 111: Typical Tensile Properties .................. 157 5456-H321: Typical Tensile Properties ................... 158 5456-H321: Creep-Rupture and Creep Properties ........... 159 5456-H323: Typical Tensile Properties ................... 160 5456-H343: Typical Tensile Properties ................... 161 Wrought Alloys: 6xxx Al-Mg-Si Alloys ...................... 162 6O05-T5 Extrusions: Typical Tensile Properties .......... 162 606l-O: Typical Tensile Properties ...................... 163 6061-O: Creep and Stress-Relaxation Properties .......... 164 6061-T4,-T451: Typical Tensile Properties ............... 165 6061-T6 Sheet and Rolled-and-Drawn Products: Typical Tensile Properties .................................... 166 6061-T6 Sheet and Rolled-and-Drawn Products: Creep- Rupture and Creep Properties .......................... 167 6061-T6, -T651, -T6511 (Except for T6 Sheet and Rolled-and-Drawn Products): Typical Tensile Properties ............................................ 168 6061-T6, -T651, -T6511 (Except for T6 Sheet and Rolled-and-Drawn Products): Creep and Stress- Relaxation Properties ................................. 169 6061-T8 Solution Heat Treated, Cold Worked 21%, and Aged 18 h at 320 °F (160 °C): Typical Tensile Properties ............................................ 170 6063-O Extrusions: Typical Tensile Properties ........... 171 6063-O Extrusions: Creep-Rupture and Creep Properties ... 172 6063-T1 Extrusions: Typical Tensile Properties .......... 173 6063-T5 Extruded Rod: Typical Tensile Properties ........ 174 6063-T5 Extrusions: Creep-Rupture and Creep Properties .. 175 6063-T6: Typical Tensile Properties ..................... 176 6063-T6: Creep-Rupture and Creep Properties ............. 177 6063-T6 Extrusions: Typical Tensile Properties .......... 178 X6064-T81 (Estimated from Data for 6061-T6 and 6061-T8): Typical Tensile Properties .................. 179 6066-T6511 Extrusions: Typical Tensile Properties ....... 180 6070-T6 Extrusions: Typical Tensile Properties .......... 181 6101-T6: Typical Tensile Properties ..................... 182 6101-T6: Creep-Rupture and Creep Properties ............. 183 6101-T61: Typical Tensile Properties .................... 184 6101-T61: Creep-Rupture and Creep Properties ............ 185 6101-T63: Typical Tensile Properties .................... 186 6101-T63: Creep-Rupture and Creep Properties ............ 187 6101-T64 (Formerly No. 2 EC): Typical Tensile Properties ............................................ 188 6101-T64 (Formerly No. 2 EC): Creep-Rupture and Creep Properties ............................................ 189 6101-T8 (Formerly No. 2 EC): Typical Tensile Properties ............................................ 190 6101-T8 (Formerly No. 2 EC): Creep-Rupture and Creep Properties ............................................ 191 6151-T6: Typical Tensile Properties ..................... 192 6151-T6: Creep-Rupture and Creep Properties ............. 192 6201-T81 Wire: Typical Tensile Properties ............... 193 6201-T81 Wire: Creep-Rupture and Creep Properties ....... 193 6262-T9: Typical Tensile Properties ..................... 194 6262-T9: Creep-Rupture and Creep Properties ............. 194 6351-T5 Extrusions: Typical Tensile Properties .......... 195 6351-T6 Extrusions: Typical Tensile Properties .......... 196 6951-0 (Estimated from Results of Tests of Similar Alloys): Typical Tensile Properties ................... 197 6951-T4 (Estimated from Results of Tests of Similar Alloys): Typical Tensile Properties ................... 197 6951-T6 (Estimated from Results of Tests of Similar Alloys): Typical Tensile Properties ................... 198 Wrought Alloys: 7xxx Al-Zn Alloys ......................... 198 7005-T53 Extrusions: Typical Tensile Properties ......... 199 7005-T53 Extrusions: Creep-Rupture and Creep Properties ............................................ 200 X7005-T6 Sheet: Typical Tensile Properties .............. 200 7005-T63, -T6351 Plate: Typical Tensile Properties ...... 201 X7007-T6 (Obsolete Alloy) Plate: Typical Tensile Properties ............................................ 202 X7007-T6 (Obsolete Alloy) Plate: Creep-Rupture and Creep Properties ...................................... 202 7039-T61, -T6151 Sheet and Plate: Typical Tensile Properties ............................................ 203 7039-T63, -T6351 Plate ≤1.5 in. (≤35.00 mm) Thick: Typical Tensile Properties ............................ 203 7050-T7451 Plate 1.001 to 2.000 in. (>25.00 ≤ 50.00 mm) Thick: Typical Tensile Properties ........... 204 7050-T7451 Plate 1.001 to 2.000 in. (>25.00 ≤ 50.00 mm) Thick: Creep-Rupture and Creep Properties ... 204 7050-Т7452 Forgings, Longitudinal Test Direction: Typical Tensile Properties ............................ 205 7075-O Extrusions: Typical Tensile Properties ........... 206 7075-O Except Extrusions: Typical Tensile Properties .... 207 Alclad 7075-O Sheet: Typical Tensile Properties ... 208 7075-T6 Die Forgings >2 in. (>50.00 mm) Thick: Typical Tensile Properties .................................... 209 7075-T6, -T6511 Extrusions 0.250 to 2.999 in. (>6.30 ≤ 75.00 mm) Thick: Typical Tensile Properties ......... 210 7075-T6, -T6511 Extrusions 0.250 to 2.999 in. (>6.30 ≤ 75.00 mm) Thick: Creep-Rupture and Creep Properties ............................................ 211 7075-T6, -T651 Except Die Forgings >2 in. (>50.00 mm) Thick and Extrusions: Typical Tensile Properties ...... 212 7075-T6, -T651 Except Die Forgings >2 in. (>50.00 mm) Thick and Extrusions: Creep-Rupture and Creep ......... 213 7075-T73: Typical Tensile Properties .................... 214 7075-T73: Creep-Rupture and Creep Properties ............ 215 7075-T76, -T651: Typical Tensile Properties ............. 216 7075-T76, -T651: Creep-Rupture and Creep Properties ..... 217 7079-T6 (Obsolete Alloy) Extrusions 0.250 to 1.499 in. (>6.30 ≤ 35.00 mm) Thick: Typical Tensile Properties .. 218 7079-T6, -T651 (Obsolete Alloy) Except Extrusions: Typical Tensile Properties ............................ 219 7079-T6, -T651 (Obsolete Alloy) Except Extrusions: Creep-Rupture and Creep Properties .................... 220 X7080-T7 (Obsolete Alloy) Forgings: Typical Tensile Properties ............................................ 221 X7080-T7 (Obsolete Alloy) Forgings: Creep-Rupture and Creep Properties ...................................... 222 X7106-T6, -T63, -T6351 (Obsolete Alloy): Typical Tensile Properties .................................... 223 X7106-T6, -T63, -T6351 (Obsolete Alloy): Creep-Rupture and Creep Properties .................................. 224 X7139-T53 (Obsolete Alloy) Extrusions: Typical Tensile Properties ............................................ 224 X7139-T6351 (Obsolete Alloy) Plate 1 in. (25.00 mm) Thick, Longitudinal: Typical Tensile Properties ....... 225 7175-T736 (Now Known as T74) Die Forgings ≤3 in. (≤75.00 mm) Thick, Longitudinal: Typical Tensile Properties ............................................ 225 7178-T6 Except Extrusions: Typical Tensile Properties ... 226 7178-T6 Except Extrusions: Creep-Rupture and Creep Properties ............................................ 227 7178-T76, -T7651: Typical Tensile Properties ............ 228 7475-T61 Sheet 0.040 to 0.249 in. (>1.00 ≤ 6.30 mm) Thick: Typical Tensile Properties ..................... 229 7475-T61 Sheet 0.040 to 0.249 in. (>1.00 ≤ 6.30 mm) Thick: Creep-Rupture and Creep Properties ............. 230 7475-T761 Sheet 0.040 to 0.249 in. (>1.00 ≤ 6.30 mm) Thick: Typical Tensile Properties ..................... 231 7475-T761 Sheet 0.040 to 0.249 in. (>1.00 ≤ 6.30 mm) Thick: Creep-Rupture and Creep Properties ............. 232 Wrought Alloys: Sxxx Al + Other Elements (Not Covered by Other Series) ......................................... 233 X8076-H19 Wire: Representative Tensile Properties ....... 233 X8081-H112 (Obsolete Alloy): Typical Tensile Properties ............................................ 234 X8081-H25 (Obsolete Alloy): Typical Tensile Properties .. 234 8280-O: Typical Tensile Properties ...................... 235 8280-H14: Typical Tensile Properties .................... 235 Cast Alloys: 2xxx Al-Cu Alloys ............................ 236 201.0-T7 Sand Castings: Typical Tensile Properties ...... 236 201.0-T7 Sand Castings: Creep-Rupture and Creep Properties ............................................ 236 224.0-T7: Typical Tensile Properties .................... 237 224.0-T7: Creep-Rupture and Creep Properties ............ 238 240.0-F Sand Castings: Typical Tensile Properties ....... 239 240.0-F Sand Castings: Creep-Rupture and Creep Properties ............................................ 239 242.0-T571 Permanent Mold: Typical Tensile Properties ... 240 242.0-T77 Sand Castings: Typical Tensile Properties ..... 241 242.0-T77 Sand Castings: Creep-Rupture and Creep Properties ............................................ 241 249.0-T7: Typical Tensile Properties .................... 242 249.0-T7: Creep-Rupture and Creep Properties ............ 242 295.0-T6 Sand Castings: Typical Tensile Properties ...... 242 295.0-T6 Sand Castings: Creep-Rupture and Creep Properties ............................................ 243 Cast Alloys: Здгхдс Al-Si + Cu or Mg Alloys ............... 244 319.0-F Sand Castings: Typical Tensile Properties ....... 244 319.0-T5 Sand Castings: Typical Tensile Properties ...... 245 332.0-T5 Permanent Mold: Typical Tensile Properties ..... 245 333.0-T5 Permanent Mold: Typical Tensile Properties ..... 246 333.0-T533 Permanent Mold: Creep-Rupture and Creep Properties ............................................ 246 333.0-T7 Permanent Mold: Typical Tensile Properties ..... 247 336.0-T551 Permanent Mold: Typical Tensile Properties ... 248 336.0-T551 Permanent Mold: Creep-Rupture Properties ..... 249 А344.0-Т4 Permanent Mold (Results of Tests on Permanent Mold Test Bars): Typical Tensile Properties ........... 249 A344.0-T4 Permanent Mold (Results of Tests on Permanent Mold Test Bars): Creep-Rupture and Creep Properties ............................................ 249 354.0-T6.-T61 Permanent Mold: Typical Tensile Properties ............................................ 250 354.0-T6, -T61 Permanent Mold: Creep-Rupture and Creep Properties ............................................ 250 355.0-T51 Sand Castings: Typical Tensile Properties ..... 251 355.0 T51-Sand Castings: Creep-Rupture and Creep Properties ............................................ 251 355.0-T6 Sand Castings: Typical Tensile Properties ...... 252 355.0-T62 Permanent Mold: Typical Tensile Properties .... 252 355.0-T62 Permanent Mold: Creep-Rupture and Creep Properties ............................................ 253 355.0-T71 Permanent Mold: Typical Tensile Properties .... 253 355.0-T71 Permanent Mold: Creep-Rupture and Creep Properties ............................................ 253 355.0-T71 Sand Castings: Typical Tensile Properties ..... 254 355.0-T71 Sand Castings: Creep-Rupture and Creep Properties ............................................ 254 A355.0-T51 Sand Castings: Typical Tensile Properties .... 255 A355.0-T51 Sand Castings: Creep-Rupture and Creep Properties ............................................ 255 C355.0-T6: Typical Tensile Properties ................... 256 C355.0-T6: Creep-Rupture and Creep Properties ........... 257 356.0-T51 Sand Castings: Typical Tensile Properties ..... 257 356.0-T6 Permanent Mold: Typical Tensile Properties ..... 258 356.0-T6 Sand Castings: Typical Tensile Properties ...... 259 356.0-T7 Permanent Mold: Typical Tensile Properties ..... 260 356.0-T7 Sand Castings: Typical Tensile Properties ...... 261 356.0-T7 Sand Castings: Creep-Rupture and Creep Properties ............................................ 261 A356.0-T6, -T61 Permanent Mold: Typical Tensile Properties ............................................ 262 A356.0-T6, -T61 Permanent Mold: Creep-Rupture and Creep Properties ...................................... 262 A359.0-T6, -T61 Permanent Mold: Typical Tensile Properties ............................................ 263 359.0-T62 Permanent Mold: Typical Tensile Properties .... 263 360.0-F Die Casting: Typical Tensile Properties ......... 264 360.0-F Die Casting: Creep-Rupture and Creep Properties ............................................ 264 A360.0-F Die Casting: Typical Tensile Properties ........ 265 380.0-F Die Casting: Typical Tensile Properties ......... 266 380.0-F Die Casting: Creep-Rupture and Creep Properties ............................................ 266 A380.0-F Die Casting: Typical Tensile Properties ........ 267 384.0-F Die Casting: Typical Tensile Properties ......... 268 384.0-F Die Casting: Creep-Rupture and Creep Properties ............................................ 268 Cast Alloys: Axxx Al-Si Alloys ............................ 269 B443.0-F Sand Casting: Typical Tensile Properties ....... 269 B443.0-F Sand Casting: Creep-Rupture and Creep Properties ............................................ 270 Cast Alloys: Sxxx Al-Mg Alloys ............................ 270 518.0-F (A218) Sand Casting (Results of Tests Made on Sand Cast Test Bars): Representative Tensile Properties ............................................ 270 520.0-T4 Sand Casting: Typical Tensile Properties ....... 271 Cast Alloys: Ixxx Al-Zn Alloys ............................ 272 710.0-F Sand Casting: Typical Tensile Properties ........ 272 Fatigue Data .................................................. 273 Fatigue Strengths of Wrought Aluminum Alloys (Approximate Average Values as Determined in Tests of Smooth and Notched R.R. Moore Rotating Beam Fatigue Machines) ........ 275 Rotating-Beam Fatigue Strengths ......................... 276 Axial Stress Fatigue Strengths of Wrought Aluminum Alloys at Various Stress Ratios (Smooth and Notched Specimens) ... 290 Axial-Stress Fatigue Strengths at Various Stress Ratios .................................................. 291 Average Fatigue Strengths for Aluminum and Aluminum Alloy Flat Sheet Specimens under Completely Reversed Flexure .... 295 Fatigue Strengths for Flat Sheet Specimens under Completely Reversed Flexure ........................... 296 Cantilever-Beam Fatigue Strengths of Aluminum Alloys at Elevated Temperatures .............................. 298 Cantilever-Beam Fatigue Tests at Elevated Temperatures ...... 298 Cantilever-Beam Fatigue Strengths of Aluminum Alloys at Elevated Temperatures Following Stabilization at the Test Temperature .................................. 304 Cantilever-Beam Tests at Elevated Temperatures (Stabilized) .............................................. 304 Appendices .................................................... 307 Appendix 1: The Aluminum Association Alloy and Temper Designation System .............................. 309 Appendix 2: Metrication of Aluminum Properties .............. 311